By viewing these pages I have read and agree to terms:

 

Modify the Aneros for E-stim

 

Disclaimer, Make these changes at your own risk, do not insert anything up your ass unless YOU and you alone are sure it will not cause damage or injury. Author and website are hereby released form all responsibility.

 

Start with any one of the Aneros stimulators. Although these are great when used alone they can be kicked up a notch by making them useable with E-Stim. Before starting to send electrical current up your ass be sure to read all the safety information and be 100% certain what you are doing will not kill you or cause harm. 1st place to start is the website www.smartstim.com. Free sign up with no spam, then read the safety first article. Above all, only use E-stim equipment designed for that specific use. Another safety first article

 

On to the how to: Before you ask, I removed the curved part that is supposed to rub under the balls because I did not like it, you do what is best for you. The following steps can be used on any solid object. It is not recommended to apply copper foil to soft or pliable toys because the foil can be cut or torn as the device is squished or flexed. Then as your remove the toy you will cut and tear your delicate internal parts and you could die.

 

The foil is used in stained glass making. (Photo 2) The 1/2 inch wide is readily available on e-bay or at your local hobby store. Since it already has a sticky backing it is a simple matter to place it where you think it will work the best.

 

Wipe the stimulator with Acetone which is fingernail polish remover. This gets the device clean and ready for the foil.

 

 

 PHOTO 3 shows the rounded end of the tape applied to the stimulator. Apply the foil all the way down and partially on the handle (Photo 3a). This way you have a conductible from top to bottom. You will have a few wrinkles and may even have a small tear. Don't worry about that right now unless the tear is all the way from side to side.  If you are not happy with the piece, pull it off, wipe down with Acetate and re-apply.  You can do this any time to try out different contact areas.

 

Now you have a single conductor applied to the device, you can repeat the process on the other side for a 2 pole or BI_POLAR electrode. Bi-polar simply means you can connect two wires to the device. Looking for the Ghost Fuck? go with the bi-polar electrode.

 

 

To smooth out the edges and top end use a round object like a ballpoint pen body to coax the wrinkles and edges down. Keep working the device for a nice feel. (Photo 4)

 

 

 

 

 

 

 

 

 

 

 

 

Photo 5 gives an example of how to connect the leads to the foil. Since both are conductive you can simple wrap the bare wire around the foil then apply a little hot glue 5a to fasten down and secure the connection. Don't worry, you can use a exacto knife to cut through the glue and remove wires if you need to make a change. I have done this several times without a problem. You can also bring both wires together in a knot on the bottom side for additional secutity.

 

 

 

 

 

 

 

 

 

 

 

 

If you run your fingers along the device you can still feel the edge of the foil which would possibly cut some important part of your body. SOLUTION: Photo 6 & 6a Use several coats of fingernail polish to level out and hold down the edge. Be sure to use several coats of polish, I used clear but you may wish to use a bright color which would be easier to see. IMPORTANT: Paint only on the very edge as the polish is an insulator meaning the naughty electrons will not flow through to stim you. SO also coat any area you do not wish to conduct electricity such as the very bottom and shaft portions.

 

My favorite is to coat with polish, most of the way to the nub that rubs the prostate. This focuses the stimulation on the prostate.   On the back side I leave most of the conductor for larger contact area. 

 

 

 

 

 

 

 

 

 

 

Photo 7 shows how smooth the final finish can be. Since all the modifications can be removed using acetone or fingernail polish remover the Aneros will not be harmed and can be changed often or returned to original condition. Some plastic toys can be damaged by acetone or other chemicals so they should be tested on a small place before being rubbed with a large amount of acetone

 

 

 

 

 

 

 

 

 

 

 

 

You can use the same technique on any object as long as it is firm and not readily pliable. Photo 8 shows a large dildo with a single band at the top. Photo 9 & 9a is a hair clip converted to clamp around a cock.

 

        

 

It is not recommended to apply copper foil to soft or pliable toys because the foil can be cut or torn as the device is squished or flexed. Then as your remove the toy you will cut and tear your delicate internal parts and you could die.

 

 

 

 

 

 

 

By viewing these pages I have read and agree to terms:

Design by Metamorphosis Design